7435A REV H Norge Dryer Parts List

Refrigerator ice and water filter (filter canister, water)

Door rack

This OEM door rack for your refrigerator is sold individually.

Drive belt

This dryer drum drive belt is 89.5" long and has four ribs. This part helps spin the drum during the drying cycle.

Belt kit (washer belt kit for Maytag models. If the washer does not agitate, spin, or drain then one of the belts could be worn and require replacement.)

There are two belts under a Maytag washer; one for the main drive pulley and one for the water pump. The belt kit includes both the drive belt and the pump belt which are both V-shaped. The belt connects the drive motor to the drive system to be able to spin the tub basket. If your washer will not agitate, not spin, or not drain, the belt could be worn or damaged and will need to be replaced. This is a genuine OEM kit. Please remember to disconnect the power and shut off the water supply to your washer before starting your repair.

Evaporator fan motor (motor ac/dc evap fan)

This 115-volt 60Hz evaporator fan motor is located in the back of the freezer and circulates air over the refrigerator coils. These coils will convert the heat into cool air, which is then circulated. If the motor has failed, the freezer/refrigerator will become too warm because the fan motor is not circulating the cool air from the freezer into the refrigerator. This is a genuine OEM part. Please remember to disconnect the power to the appliance before starting your repair.

Door catch kit (use wpl 279570)

This door catch kit contains two door strikes and three door catches to service dryer doors that have one or two catches. Make sure to read the instructions to determine which one to use for your model. These parts keep the dryer door closed to allow the dryer to operate. If your door won't stay closed or will not start you may need to replace this part. This is a genuine OEM part.

Suspension spring (spring, suspension (sold individually, 3 recommended))

This suspension spring is used to support and balance the outer tub of your washer. If the spring is broken it will cause the washer to be off balance and noisy. Check your model to see how many springs are required for your model. The spring is sold individually.

Upper roller and axle - kit of 4 (4-rlr std asm,upr rack)

The upper roller and axle attach to the upper rack to allow the dishrack to move in and out along the track of the dishwasher. This is a kit includes 4 rollers and 4 axles for your upper rack. If your dish rack is not moving in and out of the dishwasher properly you may have a broken or missing wheel and it will need to be replaced. The rollers and axles are made out of plastic and are white in color. This is a genuine OEM kit.

Lower front dishrack wheel (roller asm lwr rack frnt)

This wheel is located on the front lower rack. It includes the axle. Sold individually.

Timer knob

This timer knob for a dryer is an authentic replacement part and accepts a D-shaped shaft. The knob is white in color and measures 3 inches in diameter. The timer knob attaches onto the shaft of the timer and allows you to select the amount of time your dryer will run. If your dryer timer will not advance or your dryer will not start you may need to replace the timer knob.

Duct felt seal (lower front felt drum seal)

The duct felt seal allows the front of the drum to glide smoothly on the exterior panel while the drum is rotating. The seal is located between the back of the drum and the rear dryer panel. If the heat is escaping from the drum area causing the dryer to run too long or if there are marks on your clothes you many need to replace the duct felt seal. This is a genuine OEM part. Please remember to disconnect the power to your dryer before starting the repair.

Halogen light bulb - 120v 20w (microwave halogen light bulb, 120 volts, 20 watts.)

This clear 20-watt, 120-volt halogen light bulb is a replacement part for the bulb behind the top grill in your microwave. The light bulb is used on the inside of your microwave to provide light when the door is open, or below the microwave to provide light for the cooking area. If the bulb in the microwave is burnt out or broken you will need to replace it. This is a genuine OEM halogen light bulb and is sold individually.

Flat style oven igniter kit (sub 12400035)

The flat style gas oven igniter is used to ignite the gas to light the oven burner, which produces heat for your range. If the element has shorted out, is no longer glowing, or is glowing but only orange or red rather than white, then you will need to replace the oven igniter. When replacing the igniter please be very careful not to touch the gray element part of the igniter as it is very fragile. The igniter measures approximately 3-3/4"in length and the amperage range is 3.3 to 3.6. This igniter kit can replace igniters for either the broil or bake burners and can replace shorter and longer igniters. The kit includes the igniter, 4 wire nuts, insulation, 2 wire assembly and a bracket. This is a genuine OEM part. Please make sure to disconnect the power and shut off the gas supply before starting your repair.

Drum support roller (drum support roller - for square ported models)

This single drum support roller is used for square-ported model clothes dryers. It has a metallic bearing in its center. This support roller is used to hold the drum in place in the cabinet while letting the drum rotate on the support rollers. If your dryer is noisy, will not tumble, or takes too long to dry, you might need to replace the roller. It is recommended that you replace both rollers at once. It is sold individually.

Light bulb - 40w 130v (lamp - cavity)

This 40 watt, 130-volt clear appliance light bulb is for your microwave. The light bulb is used on the inside of your microwave to provide light when the door is open or below the microwave to provide light for the cooking area. It is clear in color and has a small screw-in base. If your current bulb is burnt out or broken you will need to replace it. This bulb is a genuine OEM part and is sold individually.